Log cabin quilt block: a 12-inch step-by-step tutorial with a 48-inch quilt plan
🖨️ Prefer to sew from paper? Printable PDF patterns are in our Etsy shop ↗
Build the classic log cabin from 2½-inch strips: one center square, ten logs added clockwise, lights on one side and darks on the other. Cutting list, sewing order, diagrams and layout ideas.
Complete guide · No signup required
A block with a story
The log cabin is one of the most traditional American quilt blocks. Strips of fabric, called logs, are sewn around a small center square, round after round, just as logs were stacked to build a cabin. Traditionally the center was red to represent the hearth, the warm heart of the home. We kept that tradition in our drawings.
Each block is divided along an imaginary diagonal: one half is made of light fabrics and the other of darks. That simple contrast is the secret of the log cabin. When you turn the blocks in different directions, the lights and darks form diamonds, zigzags, stripes or stars across the quilt, all from the same block.
Words used in this tutorial
Here are the terms you will meet. Come back to this list whenever you need it.
- Log: a strip of fabric sewn to the side of the growing block.
- Round: four logs, one on each side of the block.
- Strip: a long piece cut across the width of the fabric, here always 2½ inches wide.
- Seam allowance: always ¼ inch in quilting. All cutting sizes here already include it.
- Unfinished and finished size: the block measures ½ inch more before it is sewn into the quilt than the size you see afterwards.
What you need for one block
One block finishes at 12 × 12 inches (12½ inches before it is sewn into the quilt). All logs are 2½ inches wide and finish 2 inches wide.
| Log | Fabric | Cut length (2½ in wide) |
|---|---|---|
| Center | Red | 2½ in square |
| 1 | Light | 2½ in |
| 2 | Light | 4½ in |
| 3 | Dark | 4½ in |
| 4 | Dark | 6½ in |
| 5 | Light | 6½ in |
| 6 | Light | 8½ in |
| 7 | Dark | 8½ in |
| 8 | Dark | 10½ in |
| 9 | Light | 10½ in |
| 10 | Light | 12½ in |
Step 1: Cut the logs and center
Cut 2½-inch strips across the width of your light and dark fabrics. For one block, one light strip gives the 12½-, 10½-, 8½- and 6½-inch logs (38 inches together); the 4½- and 2½-inch lights come from a second strip. One dark strip gives all four darks (30 inches together).
Lay the logs out in order on the table, from shortest to longest, and number them with small sticky notes from 1 to 10. That way you always know which log comes next.
Step 2: Sew the first two logs
Place log 1 (light, 2½ inches) on the center square, right sides together, and sew along the right edge. Press the seam away from the center, toward the log. The unit now measures 4½ × 2½ inches.
Next, sew log 2 (light, 4½ inches) along the bottom edge of the whole unit, which is now 4½ inches long. This is the rule for the whole block: each new log goes on the next side, going clockwise (right, bottom, left, top), and it is exactly as long as that side. After log 2 the unit is a 4½-inch square.
Step 3: Keep going around, round by round
Continue clockwise: log 3 (dark, 4½ inches) on the left side, log 4 (dark, 6½ inches) on the top. Then log 5 (light, 6½) on the right, log 6 (light, 8½) on the bottom, log 7 (dark, 8½) on the left, log 8 (dark, 10½) on the top, log 9 (light, 10½) on the right and finally log 10 (light, 12½) on the bottom.
- After each log, press the seam toward the new log, away from the center.
- Measure as you go: after log 2 the unit is 4½ inches square, after log 4 it is 6½, after log 6 it is 8½, after log 8 it is 10½, and after log 10 it is 12½.
- If a log is a little too long, do not stretch the block to fit; check your seam allowance instead. If it is too short, the seams before it were too narrow.
Step 4: Check the finished block
Press the block flat and measure: 12½ inches square. Look at the colors: lights should fill the right and bottom sides, darks the left and top, meeting along the diagonal from the bottom-left corner to the top-right corner.
Each block uses 2½-inch strips of about 45 inches of lights and 30 inches of darks, which is why log cabins are so good for using up scraps.
Step 5: Plan a 48-inch quilt
Sixteen blocks in four rows of four make a 48 × 48-inch quilt, a lovely size for a sofa throw or a wall. Lay the blocks out and turn them until you find a pattern you love. With the dark halves facing the middle you get a barn-raising pattern of diamonds; with all blocks turned the same way you get diagonal stripes.
Take a photo of your favorite layout before you sew. Then sew the blocks into rows, pressing the seams of each row in the opposite direction from the row above, and join the rows.
- Lights: about 1½ yards in total (scraps welcome)
- Darks: about 1¼ yards in total
- Red centers: ⅛ yard (one 2½-inch strip gives all sixteen)
- Binding: ½ yard (six 2½-inch strips)
- Backing: 3¼ yards; batting about 56 × 56 inches
Fixing common problems
The log cabin is forgiving, but these are the usual surprises.
- Block grows crooked: a log was sewn on the wrong side. Remember: always the next side clockwise.
- Block smaller than 12½ inches: the seams were wider than ¼ inch; ten seams add up quickly.
- Wavy edges: logs were stretched to fit. Ease them gently instead, and press, do not iron.
- Lights and darks on the wrong sides: compare each log with the table before sewing.
Final thoughts
The log cabin is a calm, rhythmic block: one log at a time, always clockwise, always pressing away from the center. Make one block, measure it, and then let yourself enjoy choosing fabrics for the rest. Follow Cozy Pattern Lane on Facebook and Instagram (@cozypatternlane) for more quilting tips.