A LITTLE YARN. A LITTLE PATIENCE. SOMETHING LOVELY.
cozy pattern laneCROCHET · QUILTING · SLOW MAKING
Quilting workshop

Sew a flying-geese unit without losing the point

🖨️ Prefer to sew from paper? Printable PDF patterns are in our Etsy shop ↗

Practice one 6½ × 3½-inch unit with stitch-and-flip corners, fold checks and a quarter-inch point allowance.

Complete guide · No signup required

Keep ¼ in above the point before the next seamUnit: 6½ × 3½ in before surrounding seams
Placement schematic with exaggerated seam allowance. The upper red line is the raw edge; the dashed line is the future seam through the point. Follow the cut sizes and fold checks in the text, not the scale of this drawing.
8 min read · Reviewed November 5, 2026 · Measurements in inches · Cozy Pattern Lane editorial guide

Understand the unit before cutting

A flying-geese unit is a rectangle with a central triangle and two background corners. In this exercise, the center point faces up. The upper raw edge must retain ¼ inch above the triangle point so a later joining seam does not cut that point off.

Gather one 6½ × 3½-inch rectangle in the triangle fabric and two 3½-inch background squares. Use non-directional quilting cotton. You also need a marker, inch ruler, pins, machine, thread and iron. This is the stitch-and-flip method for one unit; do not combine these cuts with a different four-at-a-time method.

Mark opposite diagonals

On the wrong side of each background square, draw a diagonal corner to corner. Place the first square right sides together on the left end of the rectangle. Align its left, top and bottom edges. Its diagonal runs from the rectangle’s bottom-left corner toward the upper middle.

The second square will sit at the right end, with its diagonal running from the upper middle toward the bottom-right corner. These directions are mirror images. Lay both squares in position briefly to check the plan, then remove the second while sewing the first.

Sew and check the first corner

Sew directly on the marked diagonal of the first square. Fold the background outward over the outside corner and press lightly. It should cover that corner while preserving the rectangle’s original outer edges.

If the folded patch falls short, examine the drawn line, fabric alignment and fold before trimming anything. Adjust on a spare pair if necessary. A fold check is more useful than trimming first and discovering that the missing triangle cannot be replaced.

Trim the correct side of the first seam

Fold the background square back into its sewn position. Measure ¼ inch beyond the seam toward the upper-left outside corner. Cut through both layers there, leaving the seam allowance attached to the unit. Discard the excess outside triangle. Fold the background outward again and press.

Keep the large triangle fabric below the seam. Cutting on the central-triangle side would remove the intended design. Use the diagram as an orientation check, and move the cutter only when the kept and discarded areas are clear.

Repeat on the right

Place the second background square on the right end, right sides together, with its marked line from upper middle to bottom-right. Sew on that line. Fold outward and verify coverage. Then unfold, trim ¼ inch beyond the seam toward the upper-right outside corner, and press the background out.

The upper ends of the two seams overlap. That overlap leaves the necessary point allowance. Do not trim the upper edge down to the triangle’s visible point.

Use the unfinished-size checkpoint

The completed unit should measure 6½ inches across and 3½ inches high. After surrounding ¼-inch seams, the design spans 6 × 3 inches. Check the upper point allowance and that the two background corners lie flat.

Use the unfinished-size checkpoint
CheckTargetIf it differs
Raw width × height6½ × 3½ inCheck starter cuts and corner coverage
Fabric above point¼ in to upper raw edgeDo not trim to the point
Future visible design6 × 3 inAllow for all surrounding seams

Fix the cause before making a set

A clipped point in a larger block may come from this unit, the next joining seam, or both. Check the unit before blaming the final seam. A stretched rectangle may have been pulled while pressing; a short corner may come from an inaccurate diagonal.

Keep the first practice unit as a reference with its measurements written beside it. When using geese in a star or tree, follow that project’s exact sizes and orientation. This exercise teaches the method; it does not authorize substituting its unit into every design.

← Back to free tutorials