A LITTLE YARN. A LITTLE PATIENCE. SOMETHING LOVELY.
cozy pattern laneCROCHET · QUILTING · SLOW MAKING
Quilting workshop

Make two half-square triangles and trim them accurately

🖨️ Prefer to sew from paper? Printable PDF patterns are in our Etsy shop ↗

A small two-color exercise with oversized starter squares, a 3½-inch checkpoint and a clear trimming sequence.

Complete guide · No signup required

1 · Sew beside the diagonalSolid = cut; dashed = sew2 · Open, press and trim3½ × 3½ in unfinishedTwo 4-in starter squares → two trimmed units
Schematic, not a cutting template. Sew ¼ inch on both sides of the marked diagonal, cut between the seams, then press and trim each unit to 3½ inches. Only one of the two resulting units is pictured on the right.
8 min read · Reviewed November 5, 2026 · Measurements in inches · Cozy Pattern Lane editorial guide

Start with one pair, not a whole quilt

A half-square-triangle unit, or HST, is a square divided diagonally into two fabrics. Rotating identical units creates very different layouts. The useful first skill is making two units that stay square after pressing, rather than producing a large batch as quickly as possible.

For this exercise, use two non-directional quilting-cotton scraps with clear light–dark contrast. Cut one 4 × 4-inch square from each. You also need an inch-marked ruler with a 45-degree line, a fabric marker, pins, thread, a sewing machine, an iron and a rotary cutter with its mat. These are practice units, not a complete quilt pattern.

Separate the three sizes

The two 4-inch squares are oversized starters. After sewing and opening, trim each HST to 3½ × 3½ inches, including its raw seam allowances. Once that unit is sewn into surrounding patchwork with ¼-inch seams, its visible design spans 3 × 3 inches.

Do not trim to the finished 3-inch number now: doing so removes the allowance needed for the next seams. The starter size deliberately provides trimming room; it is not the size of the completed square.

Separate the three sizes
StageMeasurementWhat to check
Starter pairTwo 4 × 4 in squaresOne light and one dark
Pressed and trimmed unit3½ × 3½ inSquare corners; diagonal runs corner to corner
Visible size after surrounding seams3 × 3 in¼ in allowance on all four sides

Mark and sew the pair

On the wrong side of the lighter square, draw one diagonal from corner to opposite corner. Place the squares right sides together, aligning all four raw edges. Pin clear of the intended stitching lines.

  1. Sew one line ¼ inch from the marked diagonal on its first side. The pencil line is a cutting guide, not this stitching line.
  2. Turn or reposition the pair and sew a second line ¼ inch from the marked diagonal on its other side.
  3. Lay the pair flat on the cutting mat. Cut on the marked diagonal, between the two seams. You now have two separate folded units.

Press before measuring

Set each seam with the unit still folded. Open it gently and press the allowance toward the darker fabric for this exercise. Lift the iron instead of sliding it across the diagonal. Let the fabric cool flat before placing the ruler.

Diagonal fabric edges can stretch. If a unit bows, first inspect the seam and pressing method. Do not pull it into a square or trim it while it is held under tension; its relaxed shape is what the next seam will receive.

Trim in two passes

Place the ruler’s 45-degree line along the seam between the fabrics. Keep enough fabric beyond both trimming edges for a full 3½-inch square. Trim the first two adjacent sides, including any projecting dog ears.

Rotate the unit 180 degrees. Align the newly trimmed edges with the ruler’s 3½-inch marks, and align the diagonal again. Trim the last two sides. Recheck the width, height and diagonal. Work with your fingers clear of the blade and close the cutter before moving the ruler.

Diagnose a unit that is too small

If there is not enough fabric for a 3½-inch square, stop before trimming. Check whether the original squares were truly 4 inches, whether the seams were consistently ¼ inch from the diagonal, and whether the fabric folded along the seam during pressing.

  • A diagonal that misses a corner usually means ruler alignment needs another look.
  • A crease beside the seam steals usable width; repress gently before deciding the unit is undersized.
  • One accurate unit does not prove a batch is accurate. Measure the first pair before chain piecing.

Try two layouts on the table

Place the two finished practice units next to each other. Rotate one and observe how the diagonal changes direction. Make a second pair only after the first two are accurate, then arrange four units as a pinwheel on a design surface. Photograph or sketch the chosen placement before sewing.

Four 3½-inch units arranged two by two make a 6½-inch unfinished block after three sets of joining operations: each two-unit row is 6½ × 3½ inches, then the joined rows form the square. The visible block spans 6 inches after its outside seams. This arithmetic checks the planned dimensions; an actual sample still needs measuring.

← Back to free tutorials