A LITTLE YARN. A LITTLE PATIENCE. SOMETHING LOVELY.
cozy pattern laneCROCHET · QUILTING · SLOW MAKING
Quilting workshop

Measure quilt borders before cutting the strips

🖨️ Prefer to sew from paper? Printable PDF patterns are in our Etsy shop ↗

Use a small runner example to calculate straight borders and avoid sewing an overlong strip onto a stretched edge.

Complete guide · No signup required

Center12½ × 24½inches16½ inches unfinished28½ inches unfinished height
Diagram of the worked runner example; proportions are schematic. Green side strips are attached first, then the pink end strips. All cut dimensions are in the table.
7 min read · Reviewed October 27, 2026 · Measurements in inches · Cozy Pattern Lane editorial guide

Use measurements, not an uncut strip

This guide covers plain straight borders with butt-jointed corners: side strips first, then top and bottom strips spanning the full width. It does not cover mitered corners or pieced borders, which need their own construction plan. The worked example uses a ¼-inch seam allowance.

Before adding anything, press the quilt center and lay it flat without pulling its edges. Check its existing measurements and obvious distortions. If a large difference appears, find the construction error first. A border can help control a small amount of fullness; it cannot restore missing fabric or correct severely mismatched blocks.

Find a consistent length for both side strips

  1. Measure the center from top to bottom at three positions: near the left, through the middle and near the right. Record all three.
  2. If the differences are small and the center is otherwise sound, average the measurements: add them and divide by three.
  3. Cut two side strips to the same selected length. Their cut width comes from the border design, not from this length calculation.
  4. Mark the midpoint of each strip and the matching quilt edge. Match the ends and midpoints, then distribute only minor fullness between them.
  5. Sew with the specified allowance, press and lay the work flat again before measuring for the top and bottom.

Walk through a 12½ × 24½-inch center

Assume the pressed center measures 24½ inches long at all three positions and 12½ inches wide. We want a 2-inch finished border on every side. For this construction, cut the border strips 2½ inches wide: 2 inches visible plus ¼ inch for the seam at each long edge. The outer allowance will be used at finishing.

Cut two side strips 2½ × 24½ inches. After attaching them, the calculated width is 12½ + 2 × 2½ − 4 × ¼ = 16½ inches. Four allowances are involved: two at each of the two joins. Measure the actual result before cutting the next strips.

If the measured width agrees, cut the top and bottom strips 2½ × 16½ inches. The unfinished top becomes 16½ × 28½ inches. After the outer ¼-inch allowances are used, the nominal design size is 16 × 28 inches, before any change from quilting or washing.

Walk through a 12½ × 24½-inch center
PieceCut quantityCut dimensions
Side borders22½ × 24½ inches
Top and bottom borders22½ × 16½ inches, after checking the actual width

What if the three readings differ?

For an arithmetic example, readings of 24⅜, 24½ and 24⅝ inches total 73½ inches. Dividing by three gives 24½ inches. This average is sensible only after checking that the variation is minor and can be eased without puckers.

Do not turn averaging into a rule that hides a serious error. If one side is a full inch longer on this small center, check seam accuracy, skipped pieces and stretched bias edges. Re-measure after the correction. The size of the project and fabric behavior matter more than an arbitrary universal tolerance.

Check the first pair before adding the second

Lay the work flat after attaching and pressing the side strips. Check whether the strips ripple or pull the center into a curve. Look for stretched edges, an incorrect cut length or a tuck caught at the seam. Correct the first pair before the top and bottom lock the shape in place.

If you must piece strips to reach the required length, join them first using your chosen construction, press the join and then cut the assembled strip to the measured length. Do not assume the raw lengths simply add together; every joining seam consumes fabric.

Record the dimensions for the next stage

Write down the actual unfinished top width and height. Backing and batting planning starts from the assembled top, and your quilting method may require extra fabric around it. Keep the cutting list separate from finished dimensions so that a future remake does not confuse the two.

For a different border width, redo the cut-width calculation and both stages. Do not reuse this example’s top-strip length after changing the side borders. The order matters because the second pair spans the newly enlarged width.

← Back to free tutorials