Plan backing and binding for a small quilt
🖨️ Prefer to sew from paper? Printable PDF patterns are in our Etsy shop ↗
Separate backing size from binding length, with a worked runner example and a checklist before shopping.
Complete guide · No signup required
Start from the measured top
Backing is the fabric behind the quilt. Batting is the middle layer. Binding finishes the perimeter. They have different measurements and should have separate lines on your shopping list. This planning guide uses an example top measuring 18 × 36 inches before quilting.
Ask the person who will quilt it how much extra backing and batting they require on every side. A longarm frame often needs more allowance than a small domestic-machine project. Use that requirement, not an assumed universal minimum. The 3-inch allowance below is only an arithmetic example.
Calculate a backing rectangle
With an allowance of 3 inches on each side, add 6 inches to each dimension: 18 + 6 = 24 inches wide and 36 + 6 = 42 inches long. The backing rectangle is therefore 24 × 42 inches. Adding only 3 inches to the width would leave a total of 3 inches to share between both sides, not 3 on each side.
A fabric sold as 44 inches wide may have less usable width after removing selvages. If your actual usable width is 40 inches, the 24-inch side fits across it, while the 42-inch side must run along the length. Check print direction before choosing that orientation.
A length of 42 inches equals 1⅙ yards before trimming or shrinkage. For this example, buying 1½ yards gives 54 inches along the fabric, leaving 12 inches beyond the required rectangle before preparation. Whether that reserve is enough depends on preparation and print placement. Do not prewash a length that only just equals the required cut.
Measure around the edge for binding
For the 18 × 36-inch example, the perimeter is 2 × (18 + 36) = 108 inches. Add an example working allowance of 12 inches for turning corners and joining the final ends: the target is 120 usable inches of binding. Some finishing methods need a different allowance.
This calculation uses straight-grain double-fold binding cut in 2½-inch-wide strips, a common choice for a small straight-edged quilt. The width is a planning choice, not a universal rule. Curved edges may need bias binding, and the finishing method must match the chosen width.
Allow for the strip joins
Suppose each strip has 40 inches of usable length after selvage removal. Three raw strips total 120 inches, but diagonal joins consume length. For a planning estimate with 2½-inch strips, allow about 2½ inches per diagonal join. Three joined strips provide approximately 120 − 5 = 115 inches, which falls short of our 120-inch target.
Four strips give approximately 160 − 7½ = 152½ inches after three diagonal joins. That comfortably exceeds the target in this example. Cut four strips at 2½ inches wide: they occupy 10 inches of fabric length before squaring or preparation. One-third yard is only 12 inches; three-eighths yard is 13½ inches. Choose your purchase quantity with the actual usable width and preparation loss in mind.
Assemble and measure the strip before attaching it. A calculation should help you plan, but the final length depends on actual usable width, trimming and how the joins were made.
Keep these numbers on separate lines
| Item | Example result | Confirm before cutting |
|---|---|---|
| Quilt top | 18 × 36 inches | Actual assembled dimensions |
| Backing | 24 × 42 inches | Required allowance and usable width |
| Binding target | 120 usable inches | Your finishing method |
| Binding strips | Four at 2½ × 40 inches | Actual length after joins |
A five-minute check before shopping
When quilting is finished, follow the selected finishing method before trimming the sandwich. Do not trim away extra backing required by the quilter before the quilting takes place.
- Write units beside every measurement; do not mix inches and centimeters in one calculation.
- Check whether batting and backing allowances must be different.
- Check directional prints, matching repeats and any backing seams.
- Record usable fabric width after selvages, not only the bolt label.
- Keep backing, binding and the quilt top separate in your notes.
- Follow a complete binding attachment tutorial for corners and final joining; this page covers planning quantities.