Bind a small quilt: corners and the final join
🖨️ Prefer to sew from paper? Printable PDF patterns are in our Etsy shop ↗
Follow a separate-binding sequence, understand the 2½-inch tail overlap and check the join before trimming.
Complete guide · No signup required
Begin with a quilted and squared project
Binding covers the raw outer edges of the quilt top, batting and backing. Complete the quilting first, then square the project and trim the extra backing and batting flush. The sequence here is straight-grain, double-fold binding for a rectangular small quilt with square corners. Curved edges need a different plan.
Prepare coordinating thread, an iron, clips, an inch ruler, a needle and a machine. Cut binding strips 2½ inches wide. Check that the width and ¼-inch attachment seam suit your batting on a scrap sandwich before committing to the project.
Calculate length after allowing for strip joins
For the Little Four-Patch runner’s 20½ × 8½-inch top, the perimeter is 2 × (20½ + 8½) = 58 inches. Its instructions call for at least 70 inches of usable binding: the perimeter plus 12 inches for working and the final join.
Two 40-inch strips lose about 2½ inches at one diagonal strip join, leaving about 77½ inches before end cleanup. Measure the prepared length. Do not assume that the printed fabric width is usable width or that two nominal strips automatically provide enough.
Join the strips before attaching
Place two strip ends at right angles, right sides together. Mark and sew the diagonal across their overlap that lets the strips open into one straight length. Open the join to check alignment before trimming it to a ¼-inch allowance. Press the allowance open.
Repeat if more strips are needed. Press the long binding in half lengthwise, wrong sides together. Check its length and position joins away from the quilt’s corners. Do not fold the short end under if you intend to use the diagonal final-join method below.
Attach the first side
Start on a straight side away from a corner. Leave about 6 inches of the starting tail unattached. Place the folded binding on the quilt’s front with both raw binding edges aligned to the quilt edge. Sew with a ¼-inch seam; support the quilt and avoid pulling the binding.
Stop exactly ¼ inch before the first corner and secure the seam. That stopping distance corresponds to the attachment allowance. Mark it before reaching the corner rather than guessing while the needle is moving.
Make the corner fold
Lift the loose binding upward at 45 degrees, away from the quilt, so its raw edge extends in line with the next side. Hold that diagonal fold. Fold the binding back down along the next side, making the new top fold level with the quilt’s upper edge.
Begin sewing at the top of the new side, again ¼ inch from its raw edge. Keep the diagonal fold free of an unintended tuck. Continue around all four corners. The front miter takes shape from the folds; refine the matching back miter when wrapping the binding over.
Join the two loose tails
Approaching the start, leave a gap of about 6 inches between the attachment seams. Lay both loose tails flat along that gap. Their overlap must equal the unfolded strip width—2½ inches in this example. Trim to that overlap, then open both tails.
Bring the open tails together at right angles, right sides together, and sew the diagonal that makes a continuous strip. Before trimming the seam allowance, open the join, refold the binding and lay it around the gap. It must reach comfortably without a twist or a loose loop. If it does not, unpick and reassess the overlap and diagonal.
Finish the back and inspect
Once the trial fit is correct, trim the joining allowance to ¼ inch, press it open and refold. Finish the attachment seam across the gap. Wrap the folded binding over the edge to cover that seam on the back. Hand-stitch the folded edge to the backing, keeping stitches out of the front, and arrange the corner folds into neat miters.
Check both sides for missed sections, exposed raw edges, loose corners and tight spots that curl the quilt. Follow fabric and batting care labels. Measure the finished piece after quilting and any permitted washing; the earlier raw-top measurement is not a promise of the final bound size.