Christmas Winter Pines Trio
🖨️ Prefer to sew from paper? Printable PDF patterns are in our Etsy shop ↗
Piece three evergreen trees from graded flying-geese tiers, add charcoal trunks and frame the row with quiet cream borders.
- Raw pieced top
- 36½ × 15½ in
- Skill / units
- Confident beginner · inches
- Piecing seam
- ¼ inch, included in cut sizes
Read everything here without registering. Checkboxes keep progress only while this page remains open.

Complete written pattern · counts checked on paper. Adapted from our existing illustrated project edition and checked for written counts and assembly consistency. Fabric use, finished fit and behavior still need a physical sample. Raw-top measurements are not promises of the bound or washed size.
Fabric and tools
Amounts are planning allowances, not measured consumption from a sewn sample. Check usable fabric dimensions after preparation. For a quilting service or frame that needs more backing margin, increase the backing and batting before cutting.
| Fabric / purpose | Planning allowance |
|---|---|
| A forest, B sage and C deep green | 1 fat quarter each, at least 18 × 21 in |
| D charcoal · trunks and binding | ½ yd |
| E cream · backgrounds and borders | 1 yd |
| Backing | ¾ yd; cut 19 × 40 in |
| Batting | 19 × 40 in |
- Sewing machine, coordinating thread and a ¼-inch foot or seam guide
- Rotary cutter, cutting mat, inch-marked quilting ruler and fabric marker
- Iron, pins or clips, basting supplies, quilting foot if available and a hand-sewing needle
Complete cutting list
All sizes below include seam allowance. Dimensions are width × height unless a specific step identifies fabric length or width of fabric (WOF). Do not add a second allowance. Mark each pile before sewing.
| Piece / fabric | Quantity | Cut size |
|---|---|---|
| From EACH green · top tier | 1 rectangle each | 4½ × 2½ in |
| From EACH green · middle tier | 1 rectangle each | 6½ × 3½ in |
| From EACH green · base tier | 1 rectangle each | 8½ × 4½ in |
| E top corner squares | 6 | 2½ × 2½ in |
| E middle corner squares | 6 | 3½ × 3½ in |
| E base corner squares | 6 | 4½ × 4½ in |
| E top-tier sides | 6 | 3½ × 2½ in |
| E middle-tier sides | 6 | 2½ × 3½ in |
| E base-tier sides | 6 | 1½ × 4½ in |
| E trunk backgrounds | 6 | 5 × 2½ in |
| D trunks | 3 | 1½ × 2½ in |
| E block gaps | 2 | 1½ × 11½ in |
| E top/bottom borders | 2 | 32½ × 2½ in |
| E end borders | 2 | 2½ × 15½ in |
| D binding | 3 strips | 2½ × 42 in |
01 Prepare fabric and identify the three tree kits
Use 42 inches of usable fabric width after preparation and selvage removal. A fat quarter must be at least 18 × 21 usable inches. Cut and sew in inches; every listed piece already includes its ¼-inch allowances. Keep one green color for all three tiers of each tree.
Label the left tree A, middle B and right C. Keep their tier rectangles with corner squares of the matching height. There are nine green rectangles and eighteen cream corner squares across the whole runner. Check a ¼-inch seam with spare strips before batch piecing.
02 Make the nine flying-geese tiers
For each green rectangle, use two cream squares whose side equals the rectangle height: 2½ inches for the top, 3½ for the middle and 4½ for the base.
03 Add side backgrounds and stack each tree
Sew matching-height cream side pieces to both sides of every tier. Press toward the side backgrounds. Each completed tier row is 10½ inches wide.
| Tier | Side piece on EACH side | Raw row |
|---|---|---|
| Top | 3½ × 2½ in | 10½ × 2½ in |
| Middle | 2½ × 3½ in | 10½ × 3½ in |
| Base | 1½ × 4½ in | 10½ × 4½ in |
04 Add the trunks and finish all three blocks
With every point facing up, join the top tier to the middle and then add the base tier. Press the two horizontal seams open. The foliage section should be 10½ × 9½ inches.
Join cream 5 × 2½-inch rectangle + charcoal trunk + matching cream rectangle along their 2½-inch edges. Press away from the trunk. The row is 10½ × 2½ inches. Join it below the foliage and press toward the trunk row. Each completed block is 10½ × 11½ inches. Repeat for the other greens.
05 Join and border the tree row
Arrange A – cream gap – B – cream gap – C, with all trunks along the bottom. Use the two 1½ × 11½-inch gap strips. Join and press toward those strips. The center is 32½ × 11½ inches.
Add the two 32½ × 2½-inch borders to the top and bottom; press toward borders and check 32½ × 15½ inches. Add the two 2½ × 15½-inch end borders. The raw top should now be 36½ × 15½ inches. Measure without stretching before each new border.
06 Layer, baste and quilt
Prepare backing and batting at least 19 × 40 inches, or larger if your quilting setup requires it. Keep both oversized until quilting is complete. The planned raw top is 36½ × 15½ inches.
07 Attach the binding and finish the back
Use 3 strips cut 2½ × 42 inches. This project joins the strips with straight seams and closes the final attachment with a tucked overlap. The estimated continuous strip length before end cleanup is 125 inches. Measure the actual prepared length before attaching it.
08 Check the finished work and note actual measurements
The raw perimeter is 104 inches. Three 42-inch binding strips joined straight lose 1 inch through two joins, leaving about 125 inches before the starting fold and overlap. Keep joins away from corners.
If a tree point is missing, check its tier’s original point allowance and joining seam. If one block is short, compare its tier sizes and the trunk row before adding gaps. Follow batting quilting-distance requirements, remove pins and record actual bound dimensions. This is decorative table linen, not a tested hot-pan protector.
Keep these measurement checks beside you
| Stage | Raw / unfinished measurement |
|---|---|
| Foliage section | 10½ × 9½ in |
| One tree block | 10½ × 11½ in |
| Center with gaps | 32½ × 11½ in |
| After top/bottom borders | 32½ × 15½ in |
| Raw top | 36½ × 15½ in |
Check after pressing and cooling, without stretching. If an earlier unit is incorrect, correct it there before adding the next component.
Your project record
- Chosen fabrics, preparation method and usable widths.
- Quarter-inch seam test and first unit measurements.
- Actual backing allowance and batting quilting requirements.
- Quilting method, finished measurements and changes for a future version.
Written review: November 5, 2026. Images illustrate the design; diagrams explain placement. No physical test result is claimed.


